Festplatte beschädigt? Hilfe zu smart..
-
Hallo!
Als ich gestern meinen PC gestartet habe (Gentoo Linux), meinte fdisk
/dev/hdb wäre seit einigen tausend Tagen nicht mehr gecheckt worden.
Ich hab mir nix dabei gedacht, der Test lief ohne Fehler durch, arbeiten
war normal möglich.
Heute morgen sagte fdisk auf /dev/hdb wäre seit 1336 Tagen nichts mehr
geprüft worden.
Mh, komisch.. Platte ist eigentlich recht neu.Das sagt mir smartctl -a /dev/hdb (s.u.)
Kann damit einer von euch was anfangen? Ich nicht.
Danke für Hilfe und so schonmal im voraus
smartctl version 5.33 [i686-pc-linux-gnu] Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: SAMSUNG SP1213N Serial Number: S00UJ10XA19488 Firmware Version: TL100-24 User Capacity: 120,060,444,672 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0 Local Time is: Sun Jun 5 14:39:42 2005 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (4320) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 72) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 24 3 Spin_Up_Time 0x0007 065 001 000 Pre-fail Always - 5952 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 264 5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 253 253 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0024 253 253 000 Old_age Offline - 0 9 Power_On_Half_Minutes 0x0032 100 100 000 Old_age Always - 472h+19m 10 Spin_Retry_Count 0x0013 253 253 049 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 246 194 Temperature_Celsius 0x0022 097 082 000 Old_age Always - 47 195 Hardware_ECC_Recovered 0x000a 100 100 000 Old_age Always - 234777501 196 Reallocated_Event_Count 0x0012 253 253 000 Old_age Always - 0 197 Current_Pending_Sector 0x0033 253 253 010 Pre-fail Always - 0 198 Offline_Uncorrectable 0x0031 253 253 010 Pre-fail Offline - 0 199 UDMA_CRC_Error_Count 0x000b 100 100 051 Pre-fail Always - 1 200 Multi_Zone_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0 201 Soft_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0 SMART Error Log Version: 1 ATA Error Count: 203 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 203 occurred at disk power-on lifetime: 472 hours (19 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 00 4f c2 f0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 da 00 00 4f c2 f0 00 03:15:44.063 SMART RETURN STATUS ec 00 00 01 4f c2 f0 00 03:15:44.063 IDENTIFY DEVICE ef 02 00 00 00 00 f0 00 00:00:31.438 SET FEATURES [Enable write cache] c6 00 10 00 00 00 f0 00 00:00:31.438 SET MULTIPLE MODE 10 00 ff 00 00 00 f0 00 00:00:31.438 RECALIBRATE [OBS-4] Error 202 occurred at disk power-on lifetime: 469 hours (19 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 01 4f c2 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d9 00 01 4f c2 b0 00 00:00:15.375 SMART DISABLE OPERATIONS ec 00 ff 01 00 00 b0 00 00:00:15.375 IDENTIFY DEVICE 10 00 ff 3e c5 fa b0 00 00:00:15.375 RECALIBRATE [OBS-4] 91 00 ff 3e c5 fa bf 00 00:00:15.375 INITIALIZE DEVICE PARAMETERS [OBS-6] ec 00 ff 01 00 00 b0 00 00:00:15.313 IDENTIFY DEVICE Error 201 occurred at disk power-on lifetime: 469 hours (19 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 01 4f c2 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d9 00 01 4f c2 b0 00 00:01:34.000 SMART DISABLE OPERATIONS ec 00 ff 01 00 00 b0 00 00:01:34.000 IDENTIFY DEVICE 10 00 ff 3e c5 fa b0 00 00:01:34.000 RECALIBRATE [OBS-4] 91 00 ff 3e c5 fa bf 00 00:01:34.000 INITIALIZE DEVICE PARAMETERS [OBS-6] ec 00 ff 01 00 00 b0 00 00:01:33.938 IDENTIFY DEVICE Error 200 occurred at disk power-on lifetime: 469 hours (19 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 01 4f c2 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d9 00 01 4f c2 b0 00 00:00:37.188 SMART DISABLE OPERATIONS ec 00 ff 01 00 00 b0 00 00:00:37.188 IDENTIFY DEVICE 10 00 ff 3e c5 fa b0 00 00:00:37.188 RECALIBRATE [OBS-4] 91 00 ff 3e c5 fa bf 00 00:00:37.188 INITIALIZE DEVICE PARAMETERS [OBS-6] ec 00 ff 01 00 00 b0 00 00:00:37.125 IDENTIFY DEVICE Error 199 occurred at disk power-on lifetime: 469 hours (19 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 01 4f c2 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 d9 00 01 4f c2 b0 00 00:00:33.313 SMART DISABLE OPERATIONS ec 00 ff 01 00 00 b0 00 00:00:33.313 IDENTIFY DEVICE 10 00 ff 3e c5 fa b0 00 00:00:33.313 RECALIBRATE [OBS-4] 91 00 ff 3e c5 fa bf 00 00:00:33.313 INITIALIZE DEVICE PARAMETERS [OBS-6] ec 00 ff 01 00 00 b0 00 00:00:33.250 IDENTIFY DEVICE SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Device does not support Selective Self Tests/LoggingEdit: smartctl -H /dev/hdb sagt PASSED
-
liegt die zeit der hwclock vllt irgendwo in der vergangenheit??.. so 1336 tage? sonst würd er wohl nicht augrund der vergangenen zeit checken wollen..
-
Ich weiß nicht, wies auf anderen System ist, aber ich Stufe SMART inzwischen gemischt ein. Meine Platte ist ca. 3 Jahre alt inzwischen. Nach einem Jahr nölte SMART rum dass ein Verrecken bevorsteht. Nachdem ich SMART dann deaktiviert hatte, war Ruhe, nach ca. zwei Jahren hab ichs wiede rangemacht, wieder ein dreiviertel Jahr Ruhe, dann wieder Fehler dass es bald bergab geht. Die Platte läuft immernoch. Wie soll ich ein System mit so viel Fehlalarm ernst nehmen