4. Mplayer

Mplayer

  • S

    Moin

    Also - mein MPlayer auf einem fast frischen Gentoo macht ärger:

    snorre@snorre  $ mplayer
Using GNU internationalization
Original domain: messages
Original dirname: /usr/share/locale
Current domain: mplayer
Current dirname: /usr/share/locale

MPlayer 0.90-3.2.3 (C) 2000-2003 Arpad Gereoffy (see DOCS)

CPU: Advanced Micro Devices  (Family: 6, Stepping: 0)
Detected cache-line size is 64 bytes
CPUflags:  MMX: 1 MMX2: 1 3DNow: 1 3DNow2: 1 SSE: 0 SSE2: 0
Compiled for x86 CPU with extensions: MMX MMX2 3DNow 3DNowEx

Reading config file /usr/share/mplayer/mplayer.conf
Illegal instruction

    Dies passiert nach einem frischen Emerge. Nach einigen basteleien habe ich das standard conf file auch wieder hergestellt, und funzt immer noch nicht!
    Zur ansicht:

    ##
## MPlayer config file
##
## This file can be copied to /usr/local/etc/mplayer.conf and/or ~/.mplayer/config .
## If both exist, the ~/.mplayer/config's settings override the
## /usr/local/etc/mplayer.conf ones. And, of course command line overrides all.
## The options are the same as in the command line, but they can be specified
## more flexibly here. See below.
##

vo=sdl                  # To specify default video driver (see -vo help for
                        # list)

ao=sdl          # To specify default audio driver (see -ao help for
                        # list)

fs=yes                  # Enlarges movie window to your desktop's size.
                        # Used by drivers: all

# vm=no                 # Tries to change to a different videomode
                        # Used by drivers: dga2, x11, sdl

# bpp=0                 # Force changing display depth.
                        # Valid settings are: 0, 15, 16, 24, 32
                        # may need 'vm=yes' too.
                        # Used by drivers: fbdev, dga2, svga, vesa

# zoom=no               # Enable software scaling (powerful CPU needed)
                        # Used by drivers: svga, x11, vesa

# double=yes            # use double-buffering (recommended for xv with
                        # SUB/OSD usage)

# monitoraspect=4:3     # standard monitor size, with square pixels
# monitoraspect=16:9    # use this for widescreen monitor! non-square pixels

##
## Use GUI mode by default
##

# gui = yes

##
## Specify your preferred default skin here
## (skins are searched in /usr/local/share/mplayer/Skin/yourskin
##  and ~/.mplayer/Skin/yourskin)
##

# skin = default

##
## Multiple languages are available :)
##
## Hungarian    igen    nem
## English      yes     no
## German       ja      nein
## Spanish      si      no
## Binary       1       0
##
## You can also use spaces and/or tabs.
##

# sound         = 1
# nosound       = nein
# mixer         = /dev/mixer

##
## resample the fonts' alphamap
## 0    plain white fonts
## 0.75 very narrow black outline (default)
## 1    narrow black outline
## 10   bold black outline
##

# ffactor = 0.75

##
## FBdev driver: 

# fb = /dev/fb0                         # framebuffer device to use
# fbmode = 640x480-120                  # use this mode (read from fb.modes!)
# fbmodeconfig = /etc/fb.modes          # the fb.modes file

## VESA and FBdev driver: specify your monitor's timings
## 
## (see for example /etc/X11/XF86Config for timings!)
## ** CAUTION! IF YOUR DISPLAY DOESN'T SUPPORT AUTOMATICALLY TURNING OFF WHEN
##    OVERDRIVED (AND EVEN IF IT DOES), THIS MAY CAUSE DAMAGE TO YOUR DISPLAY!
##    WE AREN'T RESPONSIBLE, IT'S YOUR DECISION! **
##
## k, K : means multiply by 1000
## m, M : means multiply by 1.000.000
##
# monitor_hfreq = 31.5k-50k,70k         # horizontal frequency range
# monitor_vfreq = 50-90                 # vertical frequency range
# monitor_dotclock = 30M-300M           # dotclock (or pixelclock) range

##
## SDL driver
##

# vo = sdl:aalib        # use SDL video driver by default
                        # use "vo = sdl:aalib" or "vo sdl:dga" and so on,
                        # for specifying SDL subdrivers
# ao = sdl:esd          # use SDL audio driver by default
                        # use "ao = sdl:esd" to use SDL's ESD driver
# noxv = no             # whether to use XVideo hardware acceleration or not
# forcexv = yes         # force XVideo even if not detected

##
## Other (preferred to be default from configfile) switches
##

framedrop       = yes   # drop frames, when not in sync (slow CPU, videocard,
                        # etc)

cache           = 8192  # use 8Mb input cache by default

# slang         = en    # DVD : display english subtitles if available
# alang         = en    # DVD : play english audio tracks if available

## This is the correct way to use "subconfig" type options in the
## configuration file. In the command line you use :
## -aop list=resample:fout=44100 , but here it is :
# aop=list=resample:fout=44100

##
## You can also include other configfiles
## Specify full path!
##
## Delete this default :)
##

#include = /home/gabucino/.mplayer/i_did_not_RTFM_carefully_enough...

    Leider spuckt der MPlayer ja keine detailierten Info´s drüber aus, was faul ist.

    > Reading config file /usr/share/mplayer/mplayer.conf
    > Illegal instruction

    Wo ist denn nun die Illegal instruction?

    0
  • R

    Illegal Instruction ist ein Fehler, der von der CPU gemeldet wird (bzw. von der CPU an den Kernel und vom Kernel an das Programm), wenn ein falscher Opcode gelesen wird.

    Versuch am besten mal mplayer neu zu compilieren, mit anderen Einstellungen

    0
  • ?

    "./configure" vorher nicht vergessen!

    0
  • S

    ./configure ist bei einem Portage System wie Gentoo nicht nötig. Höstens man setzt vorher ein paar Umgebungssachen ala:
    USE="GTK+ -alsa" emerge something

    0
  • N

    Pass halt die CFLAGS bzw. CXXFLAGS an...

    0
Anmelden zum Antworten